Burn Error Message - Advise Please

Whalebat wrote on 3/10/2012, 4:43 PM

For a long time now I have been getting an error message at the very end of the burn process.

I haven't sought any advise to date because although I get an error dialog and fail log the project burns okay.

Can anyone advise why this happens?

Here's The Last Few Log Lines

wrote LeadIn, start DataCopy
10/03/2012 20:08:45.453:   writing leadout and closing disc
10/03/2012 20:08:45.484:   writing leadout and closing disc
10/03/2012 20:09:03.062:   writing leadout and closing disc
10/03/2012 20:09:03.093:   AVSDK Message - INFO: :Recording -> finalising disc ...
10/03/2012 20:25:54.015:   AVSDK Status - End operation Recording 673811 sectors/frames
10/03/2012 20:25:54.046:   AVSDK Message - INFO: :Recording successfully completed
10/03/2012 20:25:54.078:   AVSDK Status - Begin operation Verifying 673811 sectors/frames
10/03/2012 20:25:54.109:   AVSDK Message - INFO: :Verifying volume ...
10/03/2012 20:34:23.062:   AVSDK Message - INFO: :Verification failed, refer to previous error messages for more information
10/03/2012 20:34:23.109:   AVSDK Status - End operation Verifying 673811 sectors/frames
10/03/2012 20:34:23.125:   !!! AVSDK error: BurnToDisc() calling AvVolWriteToDisc(): 510 - verification error in volume !!!
10/03/2012 20:34:23.156:   !!! DBK error in CBurnDevSupportPoint::BurnToDisc(): 251 - verification error in volume !!!
10/03/2012 20:34:23.171:   ------------ done ----------------
10/03/2012 20:34:23.187:   Step 6 done
10/03/2012 20:34:23.218:   project burning failed
10/03/2012 20:34:23.250:   !!! DBK error in CBurnDevSupport::BurnProject(): 251 - verification error in volume !!!
10/03/2012 20:34:23.437:   !!! DBK error in BurnProject: 251 - verification error in volume !!!
10/03/2012 22:27:11.000:   WM_DEVICECHANGE( VOLUMECHANGE ) for drive e:
10/03/2012 22:27:11.031:    DEVICE REMOVAL

Comments

johnebaker wrote on 3/10/2012, 5:10 PM

Assuming the DVD's play OK in the computer DVD drive and in a DVD player then there is may be a small focusing error in the burners optical system.

I have recently changed my DVD burners to higher speed identical pair and I occasionally get a read error on verification from one of the drives, however it does not appear to affect the burned DVD's

Have you updated your burn routines to the latest aailable here

http://support2.magix.com/customer/en/download/tools

John

Whalebat wrote on 3/10/2012, 6:20 PM

Hello John

Thanks for the reply and explanation.

I have two identical drives installed as below:

BurnSupport: D: HL-DT-ST DVDRAM GH22NS40 Rev. NL00
BurnSupport: E: HL-DT-ST DVDRAM GH22NS40 Rev. NL00

No, I haven't updated any burn routines.

What are burn routines?

I noticed that the link you provided has updates for 2009 and 2010.

Would I use both of these updates or does 2010 supercede the 2009?

Please advise a little further.

Thanks In advance

johnebaker wrote on 3/11/2012, 10:04 AM

Hi Whalebat

You have a similar set up to mine - does the error occur on the second drive or both drives? Mine only occurs on the second drive when I am burning using Nero and both drives simultaneously.

The Burn routines are the software that communicates with the DVD burners and they hold settings about the different types of writers available.

You only need the latest burn routines - ie 2010.

Cheers

John

Whalebat wrote on 3/13/2012, 9:47 PM

Hello John

The 2010 Updates seem to have resolved the burn issue I was having, see image below

Thanks again

Whalebat