SF Pro 12 - How to process automation of FX parameters?

h16music wrote on 12/02/2019, 05:14

Hi,

I decided as part of building a new PC (Windows 10 Pro) to buy a new license for SF Pro 12. I thought it would be a simple and easy transition, but it has not been.

I use Waves plug-ins a lot and I tend to love automating FX parameters such as a high-pass filter frequency to give myself some really smooth DJ mixes by cutting out the lows of one of the tracks (or swapping one for the other part-way through) - a trick Darude posted online years ago.

In SF Pro 10, doing this was really easy. You used to be able to load the plug-in chainer using the button next to the play button in the file, then select your plug-in chain (in this case just Waves Q3 Stereo) and on the right side you'd see the parameters you want to automate.

I would automate "Band 1 Frq" by ticking the check box to turn it on. Then I would draw my curve in the file (i.e. from 375 Hz down to the low of 16 Hz from like the start of the file to 15 seconds later for example - 8 bars at 128 bpm). Once I like my FX parameter automation settings for the high-pass filter, I would just click on the button that is two buttons over from the play button in the plug-in chainer (looks like a gray box behind a "check box").

It is not so easy in SF Pro 12 though. I manage to get to this point:

I get stuck here. I've tried to go to FX Favourites > Apply Plug-in Chain ... and then select the same chain I used in the screenshot above, but when I click OK I either get no effect or I get the full effect but not "automated" (i.e. the high pass filter at the non-automated setting, thus cutting the frequencies for the entire selection, rather than automating the filter upwards or downwards in the frequency range as the curve would demonstrate).

What should I do?

btw, I don't have issues in terms of amount of RAM or CPU as I'm built the specs to be a workhorse, not your typical "light use" PC.

Is there any way I can do in SF Pro 12 what I used to in SF Pro 10 and actually make it work?

Comments

rraud wrote on 12/02/2019, 18:20

Prior to MAGIX acquisition, SCS (Sony Creative Software) changed the plug-in chainer (and record) GUI in Pro 11 and subsequent versions.

If you wish to apply a chain, you must select "Favorites> Apply Plug-in chain" then set up the parameters. If you select the chainer like in Pro 10, the chain is not actually applied until the file is saved. The GUI (icons and such) are different as well. See the screenshot as well as the user manual. I hope this helps.

h16music wrote on 13/02/2019, 00:19

So I have to actually "save" the file in order to apply the process every single time? I don't want to overwrite my actual audio file (songs for example) as I never had to do that in Pro 10. I think I tried doing this process and save method in Pro 12 once as per the manual but when I saved the file it literally cut the automation after 10 seconds or did something weird to the audio. It did not "render" (automate and save) as intended, so I gave up and installed Pro 10 which is not what I wanted to do.

If I do the "Favorites> Apply Plug-in chain" method, can I automate the individual parameters or is it literally a direct application of a plug-in chain set-up and no automation? (i.e. I can EQ out all highs or all lows, but I cannot do the "turning of the knob" effect that you have on a mixer where you can gradually bring in or put out the highs/lows/etc?

Why would Sony have changed such a simple process? Will Magix be returning the plug-in chainer GUI back to the SF Pro 10 set-up in a future SF Pro version?

rraud wrote on 13/02/2019, 18:15

You can adjust the FX and other paramter envelopes, so it works just like gradually turning a knob on your mixer or hardware FX.

Saving your work as a 'Sound Forge project files' <.frg> is non-destructive.

The SF Pro 11 & 12 plug-in chain automation works similar to Pro 10, just in a round-about way. SCS just made it less intuitive.. sort of like SloTools.

I have no forking idea why SCS changed such a simple process.
- I questioned SCS whilst beta testing Pro 11. There was no response to my comments and queries..

"Will Magix be returning the plug-in chainer GUI back to the SF Pro 10 set-up in a future SF Pro version?"
- I doubt it, but I do not know for sure