• SOUND FORGE

  5 answers, most recent on 8/9/2023

  RE: Sound Forge corrupts Windows 10 audio drivers
  hi @Bill-Dyszel...if you're getting white noise or static during playback, this is simply an incompatibility with your onboard sound card and the Magix Low Latency 2016 driver...removing that driver will fix the white noise/static issue.  Here's how
• SOUND FORGE

  One answer, on 9/8/2023

  RE: Hissing sound every 5 seconds
  @Charles-Miskimon  This could be caused by the Magix Low Latency Audio driver.  I don't know if you can get rid of the noise by adjusting the driver configuration.  The forum usually recommends removing the driver.  Press Windows Key + R on the
• Music Maker

  30 answers, most recent on 4/9/2025

  RE: Need help fixing magix..am losing hope
  magix music maker ASIo is now not showing. reinstalled and only 2016 low latency is showing. put in the other asios to retest..no luck. This is what its doing in action: It then crashes.. doesn't matter if instruments are recorded...loops or not.
• Samplitude

  7 answers, most recent on 4/17/2024

  RE: Wont start
  @Lars-Kristoffersen Yeah, I believe this simply shows up, if the audio driver gets enabled. Go into the program preferences. There you can select the audio driver. Usually, you want to select an ASIO driver, for example the Magix Low Latency driver.
• SOUND FORGE

  4 answers, most recent on 1/4/2024

  RE: Audio Buzz in Windows 11
  Hi @BenCWin, buzzing or screeching type sounds are symptoms of the Magix 2016 Low Latency driver issue. See this topic for instructions.https://www.magix.info/us/forum/audio-issue--1290482/#ca173899
• SOUND FORGE

  4 answers, most recent on 4/11/2025

  RE: Audio Studio 17- Opens on Win 11 Home, But Not Win 11 Pro
  @Timothy-Pugh You can also check the Windows Reliability Monitor. Press the Windows key and R on your computer keyboard and type perfmon /rel into the textbox and press Enter. This will open the Reliability Monitor. You can see where crashes
• SOUND FORGE

  7 answers, most recent on 2/16/2024

  RE: Okay, new problem with installation
  @Brandon-Montoya I think you need to uninstall the Magix Low Latency ASIO driver. Please read this comment: https://www.magix.info/us/forum/audio-issue--1290482/#ca1738999 Thank you, however I was able to follow all of the directions but the
• Samplitude

  2 answers, most recent on 3/18/2025

  RE: Latency in VST playback on Samplitude Pro x8
  Hi, Thank you so much for the advice. I've tried altering the settings you recommended to no avail I'm afraid. I have my Yamaha Clavinova CVP-305 plugged into a U6midipro box which is then plugged into my laptop via USB. The driver options i have
• SOUND FORGE

  18 answers, most recent on 6/24/2024

  RE: SoundForge Pro?
  Hi @CaseyJ, try resetting Sound Forge. 'File> "Reset all preferences and clear cached data".. If you can not open Sound Forge to access the 'File' menu, hold down the 'Ctrl+Shift' keys whilst launching SF, which should open the reset/clear cache
• SOUND FORGE

  7 answers, most recent on 2/3/2023

  RE: [Solved] Noise after installing Sound Forge 14
  @David-Bertelli This might help you Hi! this sounds like another case of the magix low latency 2016 driver interference again...i would recommend uninstalling the magix low latency driver...here's how to do it: press the Windows key + R on your
• Samplitude

  10 answers, most recent on 6/20/2024

  RE: Sampliude music studio x8 stability
  @janthyer Try to open the Audio settings in Samplitude, select an ASIO driver, for example Magix Low Latency or the ASIO driver of your audio interface. Open the ASIO driver control panel, select your audio input and audio output and set the sample
• SOUND FORGE

  12 answers, most recent on 11/20/2023

  RE: sound forge 16 glitching audio problem is back after upgrade
  Your description resembles the 'Magix 2016 Low Latency driver' issue, However, I do not recall that issue with AS-17 @Katie-Chaldecott-Gill. You can try removing the driver. See this comment from
• Samplitude

  5 answers, most recent on 1/29/2024

  RE: No sound coming from any output source
  @T-G5352 All other computer sounds (notifications, youtube, etc.) work as normal. While Samplitude is running? This shouldn't be possible while using the Magix Low Latency or Asio4All drivers. They block audio for all other applications. Your
• SOUND FORGE

  164 answers, most recent on 9/27/2023

  RE: Feedback on SOUND FORGE Pro 16
  hi @Mr._Mike_D.  this sounds like another case of the magix low latency 2016 driver interference again...i would recommend uninstalling the magix low latency driver...here's how to do it: press the Windows key + R on your computer keyboard, and type
• Samplitude

  6 answers, most recent on 9/3/2024

  RE: Samplitude Pro X8 doesn't play in RemotePC
  @sfcprw Samplitude probably uses an ASIO driver. This can be selected in the audio device settings inside the Samplitude system settings. ASIO drivers circumvent the Windows audio pipeline to decrease latency. It depends on the ASIO driver itself,
• Music Maker

  19 answers, most recent on 12/22/2023

  RE: Cant' get the Midi to fully connect with software
  @JobyJob-Mo Do you have other ASIO drivers available other than Magix Low Latency? Music Maker ASIO? You can install the free demo version of FL Studio which will also install the FL Studio ASIO driver. Maybe this driver can be selected. This
• Music Maker

  7 answers, most recent on 4/16/2023

  RE: I am using my Magix MusicMaker 17 and Zoom L-12 Live Track
  @Stefanos-Bekos You could also try the following. Select the Magix Low Latency ASIO driver. Then click on the Advanced button. You will see a list of WDM-compatible devices. Enable your Zoom device there if it is listed. Then it should theoretically
• Music Maker

  6 answers, most recent on 4/17/2023

  RE: sound card issues
  @JDG You mean 48 000 Hz? What driver have you selected in the Music Maker program settings? Magix Low Latency? Does your system use Intel SST? If that is the case you might need to activate Pull Mode (Wave RT) and Always Resample mode in the Magix
• SOUND FORGE

  13 answers, most recent on 9/25/2023

  RE: Connecting Sound Forge Audio Studio to Tascam US-322
  @Derek-Overy It also might be possible if you install an ASIO driver, for example Magix Low Latency, ASIO4ALL or FL Studio ASIO. Select the ASIO driver in the Sound Forge Audio Preferences, click on Apply, then click on Advanced and Configure to
• SOUND FORGE

  9 answers, most recent on 5/2/2023

  RE: Buggy. Introduces noise into good audio
  Regardless of the larger file size, does the noise also occur with PCM files?Do you also have a version of SF Audio Studio installed? There was a Magix Low Latency 2016 driver problem that caused system wide noise.. The low latency driver is not
• Music Maker

  5 answers, most recent on 6/27/2024

  RE: Music Maker 2025 PREMIUM
  I noticed the same with different audio drivers in past, but if I remember correctly, the Magix Low Latency Driver/ASIO works good... I currently use my Presonus Audio Interface driver as its generally flawless and issue free (with proper buffer
• Samplitude

  2 answers, most recent on 2/22/2024

  RE: [Solved] What mode to avoid inadvertently interfering with the PLAY CURSOR?
  No, it's a tower. Windows 11 Pro, 64bit, 13th Gen Intel(R) Core(TM) i7-13700   2.10 GHz, 64 GB RAM. New, lots of space, SSD, etc.Thank you for your response! I was fooling with this tonight (I'm in Germany, it's 6:45 pm here) and I think I've
• SOUND FORGE

  11 answers, most recent on 4/14/2023

  RE: Soundforge Mac Bad Crumb message
  @ronnie-l This comment here might help you https://www.magix.info/us/forum/audio-issue--1290482/#ca1738999 press the Windows key + R on your computer keyboard, and type REGEDIT in the Open field: Then navigate to:  HKEY_LOCAL_MACHINE > SOFTWARE
• Music Maker

  19 answers, most recent on 12/22/2023

  RE: Cant' get the Midi to fully connect with software
  @JobyJob-Mo Yes, thank you very much. So, this looks normal, like it should. Please make a right click on your Speakers/Headphones and open the properties. You can change the sample rate under the Advanced tab. This should be identical to the sample